How Do I Wire My DUAL Subwoofer LED Lights to My Car so They Actually Work?

Ask the people at Wal-Mart, That is where you got them right??

1. Can you see infrared LED lights?

You might notice a slight red glow in the dark, but generally, no.!! Better off to just BUY night vision googles. (The range is limited.)

2. Which types of led lights should i use for my subs?

i know they come with instructions so follow them

3. What color LED lights can you have in Texas?

do you want to modify the headlamp & back lamp? for safety reasons, better NOT change it as the current white headlamp has a good sight for driver, and the red light of back lamp is distinguishable color. if you want to decorate your vehicle, you can buy some led strip (led ribbon) and paste it on the surface of the vehicle

4. Screen won't come on but LED lights come on.?

It's a hardware problem, for sure. (updating drivers, virus protection and service packs have NOTHING to do with your problem). The motherboard is not POSTing but the problem is not necessarily the motherboard. My first guess is the RAM My second guess is the Power Supply Unit (CPU) My third guess is the board, but I would run it barebones to make sure. Honestly, it doues not sound like "this guy that looked at it" knows what the heck he is doing with troubleshooting computer hardware problems. Note: if you have a fan that is not always spinning it MUST be immediately replaced.

5. How do I make a strip of LED lights that plug into an electrical outlet and have an on/off switch?

LED's(light emitting diode) have 2 leads, one is an ANODE, the other is CATHODE. they operate at around 1.5-3 volts DC (direct current), but may vary depending on its rated voltage requirement. the wall outlet is 110 volts AC (alternating current), and from where i am(philippines), its 220 volts AC. first you have to convert the 220volts AC to DC, for that, there are available converters (opt for the converter that has many voltage settings) that are sold in stores. Secondly, it is how you connect the LED, you can connect them in parallel, all 100 of them using a wire. LED's have a polarity, and will not lit if connected on reverse, which means that you will have to connect all the anodes all together in one wire connection and cathodes all together in one wire. carefully solder them, and make sure that the 2 wire wont touch each other, or else it could get short circuit and will damage ur power converter, worst it could cause fire. after care fully checking and re checking all your connections, connect your power supply to each of the wires, set the voltage to the lowest setting(3V). and if the LED glows dimly, set it to the next higher voltage. resistor, it is a device, an electronic component that reduces or lowers the voltage by giving a resistance to the electrical current.

6. How do you turn off the LED lights on a PC fan?

you can just go in and unplug it. it wont affect anything. of course only unplug the led!

7. does anyone have the info on how to mod an amp head with LED lights?

Cool idea, but tubes already glow.... Maybe tint the plexiglass? EDIT: Okay, so I managed to find the following page, it might help. Since I am not familiar enough with a Valveking to have any idea how to tap into the existing power, you could hook up a separate circuit powered by a 9v battery or some such. Saul

8. anyone know where to get replacement LED lights for the front headlights?

Try Autozone or Advance

9. how to convert ac led lights to run off of a 12v dc boat battery?

Inverters are cheap and led lights do not need a lot of wattage

10. Stores that sell Interior LED lights for cars?

i replaced into born in 1991. whilst i replaced into born my mom offered me a evidence coin set from my start 12 months. so as that could desire to be properly worth extremely lots. perchance some thing like my wedding ceremony and engagement ring or a can of petrol. I think of that in the time of 200 years gold and petrol would be enormously uncommon and correctly worth a remarkable bit :) sturdy success with your scholarship!!